Search found 124 matches

by DP_Sam
September 17th, 2015, 4:07 pm
Forum: iBCS User Forum
Topic: iBootBar & iBoot Cloud - to be or not to be ?
Replies: 7
Views: 46202

Re: iBootBar & iBoot Cloud - to be or not to be ?

The cloud was introduced after the iBootBar was. As you surmised, the current firmware is the issue with cloud support, not the hardware. Since the hardware for the iBootBar is already in re-design, there are no plans to update the current iBootBar code to support the cloud. Cloud support will be in...
by DP_Sam
September 17th, 2015, 8:38 am
Forum: iBoot
Topic: Products suggestiong: DNS and Wake On LAN
Replies: 1
Views: 19376

Re: Products suggestiong: DNS and Wake On LAN

The new iBoot-G2 code (1.30.162) should announce itself when using DHCP. We are adding that feature as implemented into the new release of iBoot-G2+ code. (That code is currently in test) The "Wake on Lan" command is not as widely used. Most customers can make a change in the BIOS of the PC to force...
by DP_Sam
September 16th, 2015, 4:10 pm
Forum: iBCS User Forum
Topic: iBootBar & iBoot Cloud - to be or not to be ?
Replies: 7
Views: 46202

Re: iBootBar & iBoot Cloud - to be or not to be ?

The current iBootBar does not support the cloud.

The idea is being considered though, and will probably be included as a feature in future hardware iBootBar designs.
by DP_Sam
September 1st, 2015, 8:06 am
Forum: iBoot
Topic: Iboot original ..I cant connect
Replies: 6
Views: 33804

Re: Iboot original ..I cant connect

You do not want to redirect the same port to the iBoot as the cameras. This would make the public ip not know where to redirect traffic internally. (Unless you are disconnecting the cameras temporarily as a test.) I would avoid 8080 as well if you were considering that as a port. Lastly, the origina...
by DP_Sam
August 31st, 2015, 3:39 pm
Forum: iBoot
Topic: Iboot original ..I cant connect
Replies: 6
Views: 33804

Re: Iboot original ..I cant connect

The iBoot-HUB is programmed by default to use port 80. I assume you are using that port for the PC or security cameras. When you are local to the device log onto it, and change the default webport to be something non standard, and then redirect that port to the local ip address for the iBoot. Then y...
by DP_Sam
August 19th, 2015, 2:09 pm
Forum: iBoot
Topic: unable to open browser
Replies: 3
Views: 24663

Re: unable to open browser

I have no doubt your experience with the older iBoots will be invaluable, but setup is different. Since you have not been able to access the iBoot-G2, the subnet mask is still going to be 255.255.250.0 and the gateway will be 192.168.1.1. These are obviously not correct for your network. Can you tem...
by DP_Sam
August 19th, 2015, 10:08 am
Forum: iBoot
Topic: unable to open browser
Replies: 3
Views: 24663

Re: unable to open browser

I am sorry to hear you are having issues. I will need to know the ipaddress of the units and the PC and how you set them. ( including subnet mask if not 255.255.255.0 and port being used if not 80) It sounds as if there is an ip conflict, or a subnet mask issue. Another possibility is that when you ...
by DP_Sam
July 28th, 2015, 3:26 pm
Forum: iBootBar
Topic: iBootBar SNMP monitoring
Replies: 6
Views: 33202

Re: iBootBar SNMP monitoring

Sorry for the delay.

A You are using the command:
  • snmpwalk -v2c -c public ibootbar01.oursubnet.local
I suspect this may work:
  • snmpwalk -v1 -c public ibootbar01.oursubnet.local
B Looks like the variables you are trying to get are standard SNMP variables, but are not supported by the iBB.
by DP_Sam
July 28th, 2015, 9:40 am
Forum: iBootBar
Topic: Setting up a iBoot bar cluster
Replies: 8
Views: 35922

Re: Setting up a iBoot bar cluster

Cluster setups are meant to be close in proximity to each other and need to be connected via the expansion jacks on the rear of the units. You can keep the network connection as well, but just making the setting changes will not make the units communicate as cluster through the network. That being s...
by DP_Sam
July 9th, 2015, 3:41 pm
Forum: iBootBar
Topic: iBootBar SNMP monitoring
Replies: 6
Views: 33202

Re: iBootBar SNMP monitoring

Can you tell me more about the command you are using?
Is it a unix command line or a windows stand alone application that you are passing parameters to?